Tools & LS Specialty Tools

Tools & LS Specialty Tools

35 products

    Various LS engine related tools to aid you with that LS rebuild.

    Camshaft install tools help prevent bearing damage when sliding the cam into place.

    Make sure the front main seal is aligned correctly with an alignment sleeve.

    Need to lock the crank to get that balancer bolt undone? Check the new billet flex plate holding tool.

    Torque plates are used when boring and honing engine blocks to simulate the stresses and distortions of an assembled engine.

    If you have a workshop check out our Mechanics Mate Category for high speed high quality hydraulic pullers.

    35 products
    Crow Cams 11 Inch Cam Degree Wheel Suit LS1 LS2 LS3
    LS Heavy Duty Flywheel Flexplate Crank Holding Tool Flex Plate Stop LS1 LSX LS3
    Sold Out
    Cam Bearing Installation/Removal Tool suits LS engines only
    LS LT Harmonic Balancer Pulley Install Tool LS1 LT1
    LS Crank Pin Dowel Kit LS1 LS2 LS3 LSX Crankshaft Balancer LSA Tool Drill Jig
    LS Valve Stem Seal Installation Tool Install Driver Tool .500 .530 LSX L98 LS3 LS1
    LS Truck Block - 4.8L 5.3L Iron Block Drill Template
    Sold Out
    LS Timing Cover Seal Alignment Tool LS1 LS3 LSX Plate Align Sleeve ICT Billet
    Engine Safe Stand Adapter Plate Chevy LS1 Duramax BBC SBC LS Heavy Duty Support
    Engine Safe Stand Adapter Plate Chevy LS1 Duramax BBC SBC LS Heavy Duty Support
    LS T56 TR6060 Clutch Alignment tool VT VX VY VZ VE VF 5.7 6.0L
    Ford 9" Rear End Axle Tube Narrowing Cut Guide Rearend Pinion Dogbone Tool
    LS1 Harmonic Balancer Puller Tool Crank Crankshaft Pulley LS LSX LS2 LS3 LQ4 LQ9 5.3L 6.0L
    Pro Series 12" Camshaft Install Tool (for LS 3 bolt Cams -SBC & BBC)
    Sold Out
    Summit Racing® Cam Degreeing Kit
    Plastigage .001-.003 Range Green Mahle Clevite
    Sold Out
    LS Torque Plate Engine Block Machining Boring Honing Cylinder Motor 4.20
    Sold Out
    Sold Out
    COMP Cams Hi-Tech Pushrod Length Checking Tool 7702-1 6.800 - 7.800 in
    Performance Tool Power Steering Pump Pulley Installer
    3pc Billet Aluminum Wrench Set 6 8 10 AN Fitting Spanners/Wrenches
    Plastigage .009-.020 Range Yellow Mahle Clevite
    Plastigage .002-.006 Range RED Mahle Clevite
    fuel line bender
    Earl's Performance Standard Tubing/Pipe Benders 180°
    Billet Aluminum AN Fitting Spanner X12 Wrench Complete Set USA MADE
    Pilot Bearing Installation Handle 6" Spigot Bush Install Tool T56 TR6060
    Plastigage .004-.009 Range BLUE Mahle Clevite
    LS Gen 3 Iron Block to Gen 4 Timing Chain Guide Drill Template Tool LQ4 L33 LQ9
    SBC Engine / Frame Motor Mount Alignment Tool Small Block Chevy Jig LS Swap
    Master Tester Kit 4AN 6AN 8AN 10AN 12AN to 1/4" Air Compressor Hose Testing Tool
    Mini Tubing / Pipe Cutters 3 - 16 mm / 1/8"-5/8"
    Flare Tool Double 45° Flare, Tube Sizes 3/16, 1/4, 5/16, 3/8, 1/2 in Kit
    6" Camshaft Installation Handle (for LS Gen IV Cam) 4 Tool Malex Motorsports Australia
    6" Camshaft Installation Handle (for LS Gen IV Cam) 4 Tool
    Recently viewed